summaryrefslogtreecommitdiffhomepage
path: root/readme.md
blob: 770b472ac8ac76138e90bf7b32678ff301b83a8a (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
% xmobar - a minimalistic status bar

# About

xmobar is a minimalistic, mostly text based, status bar. It was
originally designed and implemented by Andrea Rossato to work with
[xmonad], but it's actually usable with any window-manager.

xmobar was inspired by the [Ion3] status bar, and supports similar
features, like dynamic color management, icons, output templates, and
extensibility through plugins.

This page documents xmobar 0.24.3 (see [release notes]).

[This screenshot] shows xmobar running under [sawfish], with
antialiased fonts. And [this one] is my desktop with [xmonad] and two
instances of xmobar.

[release notes]: http://projects.haskell.org/xmobar/releases.html
[xmonad]: http://xmonad.org
[Ion3]: http://tuomov.iki.fi/software/
[This screenshot]: http://projects.haskell.org/xmobar/xmobar-sawfish.png
[this one]: http://projects.haskell.org/xmobar/xmobar-xmonad.png

# Bug Reports

To submit bug reports you can use the [bug tracker over at Github] or
send mail to our [Mailing list].

Note: the old bug tracker at Google code is deprecated.  Please use
Github's for new bugs.

[bug tracker over at Github]: https://github.com/jaor/xmobar/issues

# Installation

## Using cabal-install

Xmobar is available from [Hackage], and you can install it using
`cabal-install`:

        cabal install xmobar

See below for a list of optional compilation flags that will enable
some optional plugins. For instance, to install xmobar with all the
bells and whistles, use:

        cabal install xmobar --flags="all_extensions"

## From source

If you don't have `cabal-install` installed, you can get xmobar's
source code in a variety of ways:

  - From [Hackage]. Just download the latest release from xmobar's
    hackage page.
  - From [Github]. You can also obtain a tarball in [Github's
    downloads page]. You'll find there links to each tagged release.
  - From the bleeding edge repo. If you prefer to live dangerously,
    just get the latest and greatest (and buggiest, I guess) using
    git:

        git clone git://github.com/jaor/xmobar


[Github's downloads page]: https://github.com/jaor/xmobar/downloads

If you have cabal installed, you can now use it from within xmobar's
source tree:

        cabal install -fall_extensions


Otherwise, run the configure script:

        runhaskell Setup.lhs configure

        # To enable UTF-8 support run:
        runhaskell Setup.lhs configure --flags="with_utf8"

        # To enable both XFT and UTF-8 support run:
        runhaskell Setup.lhs configure --flags="with_xft"

        # To enable all extensions
        runhaskell Setup.lhs configure --flags="all_extensions"

Now you can build the source:

        runhaskell Setup.lhs build
        runhaskell Setup.lhs install # possibly to be run as root


## Optional features

You can configure xmobar to include some optional plugins and
features, which are not compiled by default. To that end, you need to
add one or more flags to either the cabal install command or the
configure setup step, as shown in the examples above.

Extensions need additional libraries (listed below) that will be
automatically downloaded and installed if you're using cabal install.
Otherwise, you'll need to install them yourself.

`with_dbus`
:    Enables support for DBUS by making xmobar to publish a service on
     the session bus.  Requires the [dbus] package.

`with_threaded`
:    Uses GHC's threaded runtime.  Use this option if xmobar enters a
     high-CPU regime right after starting.

`with_utf8`
:    UTF-8 support. Requires the [utf8-string] package.

`with_xft`
:    Antialiased fonts. Requires the [X11-xft] package. This option
     automatically enables UTF-8.

     To use XFT fonts you need to use the `xft:` prefix in the `font`
     configuration option. For instance:

        font = "xft:Times New Roman-10:italic"

     Or to have fallback fonts, just separate them by commas:

        font = "xft:Open Sans:size=9,WenQuanYi Zen Hei:size=9"

`with_mpd`
:    Enables support for the [MPD] daemon. Requires the [libmpd] package.

`with_mpris`
:    Enables support for MPRIS v1/v2 protocol.
     Requires the [dbus] and [text] packages.

`with_inotify`
:    Support for inotify in modern Linux kernels. This option is needed
     for the MBox and Mail plugins to work. Requires the [hinotify]
     package.

`with_iwlib`
:    Support for wireless cards. Enables the Wireless plugin. No Haskell
     library is required, but you will need the [iwlib] C library and
     headers in your system (e.g., install `libiw-dev` in Debian-based
     systems).

`with_alsa`
:    Support for ALSA sound cards. Enables the Volume plugin. Requires the
     [alsa-mixer] package.  To install the latter, you'll need the
     [libasound] C library and headers in your system (e.g., install
     `libasound2-dev` in Debian-based systems).

`with_datezone`
:    Support for other timezones. Enables the DateZone plugin.
     Requires [timezone-olson] and [timezone-series] package.

`with_xpm`
:    Support for xpm image file format. This will allow loading .xpm files in `<icon>`.
     Requires the [libXpm] C library.

`with_uvmeter`
:    Enables UVMeter plugin. The plugin shows UV data for Australia.

`with_conduit`
:    Use http-conduit for getting weather data enabling support for http proxies.
     Requires [http-conduit] and [http-types].

`all_extensions`
:    Enables all the extensions above.

# Running xmobar

You can now run xmobar with:

        xmobar /path/to/config &

or

        xmobar &

if you have the default configuration file saved as
`$XDG\_CONFIG\_HOME/xmobar/xmobarrc` (defaulting to
`~/.config/xmobar/xmobarrc`), or `~/.xmobarrc`.

## Signal Handling

Since 0.14 xmobar reacts to SIGUSR1 and SIGUSR2:

- After receiving SIGUSR1 xmobar moves its position to the next screen.

- After receiving SIGUSR2 xmobar repositions itself on the current screen.

# Configuration

## Quick Start

See [samples/xmobar.config] for an example.

[samples/xmobar.config]: http://github.com/jaor/xmobar/raw/master/samples/xmobar.config

For the output template:

- `%command%` will execute command and print the output. The output
  may contain markups to change the characters' color.

- `<fc=#FF0000>string</fc>` will print `string` with `#FF0000` color
  (red).

- `<fn=1>string</fn>` will print `string` with the first font from
  `additionalFonts`.  The index `0` corresponds to the standard font.

- `<icon=/path/to/icon.xbm/>` will insert the given bitmap. XPM image
  format is also supported when compiled with `--flags="with_xpm"`.

- ```<action=`command` button=12345>``` will execute given command
  when clicked with specified buttons. If not specified, button is
  equal to 1 (left mouse button). Using old syntax (without backticks
  surrounding `command`) will result in `button` attribute being
  ignored.

- `<raw=len:str/>` allows the encapsulation of arbitrary text `str` (which
  must be `len` `Char`s long, where `len` is encoded as a decimal sequence).
  Careful use of this and `UnsafeStdinReader`, for example, permits window
  managers to feed xmobar strings with `<action>` tags mixed with un-trusted
  content (e.g. window titles).  For example, if xmobar is invoked as

    ```xmobar -c "[Run UnsafeStdinReader]" -t "%UnsafeStdinReader%"```

  and receives on standard input the line

    ```<action=`echo test` button=1><raw=41:<action=`echo mooo` button=1>foo</action>/></action>```

  then it will display the text ```<action=`echo mooo` button=1>foo</action>```,
  which, when clicked, will cause `test` to be echoed.

Other configuration options:

`font`
:    Name of the font to be used. Use the `xft:` prefix for XFT fonts.

`additionalFonts`
:    Haskell-style list of fonts to be used with the `fn`-template.
     Use the `xft:` prefix for XFT fonts.

`bgColor`
:    Background color.

`fgColor`
:    Default font color.

`alpha`
:    The transparency.  0 is transparent, 255 is opaque.

`position`
:     Top, TopP, TopW, TopSize, Bottom, BottomP, BottomW, BottomSize or Static
      (with x, y, width and height).

:     TopP and BottomP take 2 arguments: left padding and right padding.

:     TopW and BottomW take 2 arguments: an alignment parameter (L for
      left, C for centered, R for Right) and an integer for the
      percentage width xmobar window will have in respect to the
      screen width.

:     TopSize and BottomSize take 3 arguments: an alignment parameter, an
      integer for the percentage width, and an integer for the minimum pixel
      height that the xmobar window will have.

:     For example:

:          position = BottomW C 75

:     to place xmobar at the bottom, centered with the 75% of the screen width.

:     Or:

:          position = BottomP 120 0

:    to place xmobar at the bottom, with 120 pixel indent of the left.


:     Or

:          position = Static { xpos = 0 , ypos = 0, width = 1024, height = 15 }

:     or

:         position = Top

`textOffset`
:     The vertical offset, in pixels, for the text baseline.  If
      negative or not given, xmobar will try to center text
      vertically.

`iconOffset`
:     The vertical offset, in pixels, for icons bottom line.  If negative
      or not given, xmobar will try to center icons vertically.

`lowerOnStart`
:     When True the window is sent the bottom of the window stack initially.

`hideOnStart`
:     When set to True the window is initially not mapped, i.e. hidden. It then
      can be toggled manually (for example using the dbus interface) or
      automatically (by a plugin) to make it reappear.

`allDesktops`
:     When set to True (the default), xmobar will tell the window manager
      explicitly to be shown in all desktops, by setting
      `_NET_WM_DESKTOP` to 0xffffffff.

`overrideRedirect`
:     If you're running xmobar in a tiling window manager, you might need
      to set this option to `False` so that it behaves as a docked
      application.  Defaults to `True`.

`pickBroadest`
:     When multiple displays are available, xmobar will choose by default
      the first one to place itself.  With this flag set to `True`
      (the default is `False`) it will choose the broadest one
      instead.

`persistent`
:     When True the window status is fixed i.e. hiding or revealing is not
      possible. This option can be toggled at runtime. Defaults to False.

`border`
:     TopB, TopBM, BottomB, BottomBM, FullB, FullBM or NoBorder (default).

:     TopB, BottomB, FullB take no arguments, and request drawing a
      border at the top, bottom or around xmobar's window,
      respectively.

:     TopBM, BottomBM, FullBM take an integer argument, which is the
      margin, in pixels, between the border of the window and the
      drawn border.

`borderColor`
:     Border color.

`borderWidth`
:     Border width in pixels.

`iconRoot`
:     Root folder where icons are stored. For <icon=path/>
      if path start with `"/"`, `"./"` or `"../"` it is interpreted as
      it is.  Otherwise it will have `iconRoot ++ "/"` prepended to
      it. Default is `"."`.

`commands`
:    For setting the options of the programs to run (optional).

`sepChar`
:    The character to be used for indicating commands in the output
     template (default '%').

`alignSep`
:    a 2 character string for aligning text in the output template. The
     text before the first character will be align to left, the text in
     between the 2 characters will be centered, and the text after the
     second character will be align to the right.

`template`
:    The output template.

### Running xmobar with i3status

xmobar can be used to display information generated by [i3status], a
small program that gathers system information and outputs it in
formats suitable for being displayed by the dzen2 status bar, wmii's
status bar or xmobar's `StdinReader`.  See [i3status manual] for
further details.

## Command Line Options

xmobar can be either configured with a configuration file or with
command line options. In the second case, the command line options
will overwrite the corresponding options set in the configuration
file.

Example:

    xmobar -B white -a right -F blue -t '%LIPB%' -c '[Run Weather "LIPB" [] 36000]'

This is the list of command line options (the output of
xmobar --help):

    Usage: xmobar [OPTION...] [FILE]
    Options:
      -h, -?        --help                 This help
      -V            --version              Show version information
      -f font name  --font=font name       The font name
      -B bg color   --bgcolor=bg color     The background color. Default black
      -F fg color   --fgcolor=fg color     The foreground color. Default grey
      -A alpha      --alpha=alpha          The transparency: 0 is transparent, 255 (the default) is opaque
      -o            --top                  Place xmobar at the top of the screen
      -b            --bottom               Place xmobar at the bottom of the screen
      -p            --position=position    Specify position, same as in config file
      -d            --dock                 Try to start xmobar as a dock
      -a alignsep   --alignsep=alignsep    Separators for left, center and right text
                                           alignment. Default: '}{'
      -s char       --sepchar=char         The character used to separate commands in
                                           the output template. Default '%'
      -t template   --template=template    The output template
      -i path       --iconroot=path        Default directory for icon pattern files
      -c commands   --commands=commands    The list of commands to be executed
      -C command    --add-command=command  Add to the list of commands to be executed
      -x screen     --screen=screen        On which X screen number to start

    Mail bug reports and suggestions to <xmobar@projects.haskell.org>

## The DBus Interface

When compiled with the optional `with_dbus` flag, xmobar can be
controlled over dbus. All signals defined in [src/Signal.hs] as `data
SignalType` can now be sent over dbus to xmobar.  Due to current
limitations of the implementation only one process of xmobar can
acquire the dbus. This is handled on a first-come-first-served basis,
meaning that the first process will get the dbus interface. Other
processes will run without further problems, yet have no dbus
interface.

[src/Signal.hs]: https://github.com/jaor/xmobar/raw/master/src/Signal.hs

- Bus Name: `org.Xmobar.Control`
- Object Path: `/org/Xmobar/Control`
- Member Name: Any of SignalType, e.g. `string:Reveal`
- Interface Name: `org.Xmobar.Control`

An example using the `dbus-send` command line utility:

        dbus-send \
            --session \
            --dest=org.Xmobar.Control \
            --type=method_call \
            --print-reply \
            '/org/Xmobar/Control' \
            org.Xmobar.Control.SendSignal \
            "string:Toggle 0"

It is also possible to send multiple signals at once:

        # send to another screen, reveal and toggle the persistent flag
        dbus-send [..] \
            "string:ChangeScreen 0" "string:Reveal 0" "string:TogglePersistent"

The `Toggle`, `Reveal`, and `Hide` signals take an additional integer
argument that denotes an initial delay, in tenths of a second, before
the command takes effect.

### Example for using the DBus IPC interface with XMonad

Bind the key which should {,un}map xmobar to a dummy value. This is necessary
for {,un}grabKey in xmonad.

    ((0, xK_Alt_L   ), return ())

Also, install `avoidStruts` layout modifier from `XMonad.Hooks.ManageDocks`

Finally, install these two event hooks (`handleEventHook` in `XConfig`)
`myDocksEventHook` is a replacement for `docksEventHook` which reacts on unmap
events as well (which `docksEventHook` doesn't).

    import qualified XMonad.Util.ExtensibleState as XS

    data DockToggleTime = DTT { lastTime :: Time } deriving (Eq, Show, Typeable)

    instance ExtensionClass DockToggleTime where
        initialValue = DTT 0

    toggleDocksHook :: Int -> KeySym -> Event -> X All
    toggleDocksHook to ks ( KeyEvent { ev_event_display = d
                                     , ev_event_type    = et
                                     , ev_keycode       = ekc
                                     , ev_time          = etime
                                     } ) =
            io (keysymToKeycode d ks) >>= toggleDocks >> return (All True)
        where
        toggleDocks kc
            | ekc == kc && et == keyPress = do
                safeSendSignal ["Reveal 0", "TogglePersistent"]
                XS.put ( DTT etime )
            | ekc == kc && et == keyRelease = do
                gap <- XS.gets ( (-) etime . lastTime )
                safeSendSignal [ "TogglePersistent"
                               , "Hide " ++ show (if gap < 400 then to else 0)
                               ]
            | otherwise = return ()

        safeSendSignal s = catchX (io $ sendSignal s) (return ())
        sendSignal    = withSession . callSignal
        withSession mc = connectSession >>= \c -> callNoReply c mc >> disconnect c
        callSignal :: [String] -> MethodCall
        callSignal s = ( methodCall
                         ( objectPath_    "/org/Xmobar/Control" )
                         ( interfaceName_ "org.Xmobar.Control"  )
                         ( memberName_    "SendSignal"          )
                       ) { methodCallDestination = Just $ busName_ "org.Xmobar.Control"
                         , methodCallBody        = map toVariant s
                         }

    toggleDocksHook _ _ _ = return (All True)

    myDocksEventHook :: Event -> X All
    myDocksEventHook e = do
        when (et == mapNotify || et == unmapNotify) $
            whenX ((not `fmap` (isClient w)) <&&> runQuery checkDock w) refresh
        return (All True)
        where w  = ev_window e
              et = ev_event_type e


## The Output Template

The output template must contain at least one command. xmobar will
parse the template and will search for the command to be executed in
the `commands` configuration option. First an `alias` will be searched
(plugins such as Weather or Network have default aliases, see below).
After that, the command name will be tried. If a command is found, the
arguments specified in the `commands` list will be used.

If no command is found in the `commands` list, xmobar will ask the
operating system to execute a program with the name found in the
template. If the execution is not successful an error will be
reported.

It's possible to insert in the global templates icon directives of the
form:

     <icon=/path/to/bitmap.xbm/>

which will produce the expected result. Accepted image formats are XBM
and XPM (when `with_xpm` flag is enabled). If path does not start with
`"/"`, `"./"`, `"../"` it will have `iconRoot ++ "/"` prepended to it.

It's also possible to use action directives of the form:

     <action=`command` button=12345>

which will be executed when clicked on with specified mouse buttons. This tag
can be nested, allowing different commands to be run depending on button clicked.

## The `commands` Configuration Option

The `commands` configuration option is a list of commands information
and arguments to be used by xmobar when parsing the output template.
Each member of the list consists in a command prefixed by the `Run`
keyword. Each command has arguments to control the way xmobar is going
to execute it.

The option consists in a list of commands separated by a comma and
enclosed by square parenthesis.

Example:

    [Run Memory ["-t","Mem: <usedratio>%"] 10, Run Swap [] 10]

to run the Memory monitor plugin with the specified template, and the
swap monitor plugin, with default options, every second.  And here's
an example of a template for the commands above using an icon:

    template="<icon=/home/jao/.xmobar/mem.xbm/><memory> <swap>"

This example will run "xclock" command when date is clicked:

    template="<action=`xclock`>%date%</action>

The only internal available command is `Com` (see below Executing
External Commands). All other commands are provided by plugins. xmobar
comes with some plugins, providing a set of system monitors, a
standard input reader, an Unix named pipe reader, a configurable date
plugin, and much more: we list all available plugins below.

Other commands can be created as plugins with the Plugin
infrastructure. See below.

## System Monitor Plugins

This is the description of the system monitor plugins available in
xmobar.  Some of them are only installed when an optional build option
is set: we mention that fact, when needed, in their description.

Each monitor has an `alias` to be used in the output template.
Monitors have default aliases.  The sections below describe every
monitor in turn, but before we provide a list of the configuration
options (or *monitor arguments*) they all share.

### Icon patterns

Some monitors allow usage of strings that depend on some integer value
from 0 to 8 by replacing all occurrences of `"%%"` with it
(i.e. `"<icon=/path/to/icon_%%.xpm/>"` will be interpreted
as `"<icon=/path/to/icon_3.xpm/>"` when the value is `3`, also `"%"` is interpreted
as `"%"`, `"%%"` as `"3"`, `"%%%"` as `"3%"`, `"%%%%"` as `"33"` and so on). Essentially
it allows to replace vertical bars with custom icons. For example,

    Run Brightness
      [ "-t", "<ipat>"
      , "--"
      , "--brightness-icon-pattern", "<icon=bright_%%.xpm/>"
      ] 30

Will display `bright_0.xpm` to `bright_8.xpm` depending on current brightness
value.

### Default Monitor Arguments

Monitors accept a common set of arguments, described in the first
subsection below.  In addition, some monitors accept additional options
that are specific to them.  When specifying the list of arguments in
your configuration, the common options come first, followed by "--",
followed by any monitor-specific options.

These are the options available for all monitors below:

- `-t` _string_  Output template
    - Template for the monitor output. Field names must be enclosed
      between pointy brackets (`<foo>`) and will be substituted by the
      computed values. You can also specify the foreground (and
      optionally, background) color for a region by bracketing it
      between `<fc=fgcolor>` (or `<fc=fgcolor,bgcolor>`) and
      `</fc>`. The rest of the template is output verbatim.
    - Long option: `--template`
    - Default value: per monitor (see above).
- `-H` _number_ The high threshold.
    - Numerical values higher than _number_ will be displayed with the
      color specified by `-h` (see below).
    - Long option: `--High`
    - Default value: 66
- `-L` _number_ The low threshold.
    - Numerical values higher than _number_ and lower than the high
      threshold will be displayed with the color specified by `-n`
      (see below). Values lower than _number_ will use the `-l` color.
    - Long option: `--Low`
    - Default value: 33
- `-h` _color_  High threshold color.
    - Color for displaying values above the high threshold. _color_ can
      be either a name (e.g. "blue") or an hexadecimal RGB (e.g.
      "#FF0000").
    - Long option: `--high`
    - Default: none (use the default foreground).
- `-n` _color_  Color for 'normal' values
    - Color used for values greater than the low threshold but lower
      than the high one.
    - Long option: `--normal`
    - Default: none (use the default foreground).
- `-l` _color_  The low threshold color
    - Color for displaying values below the low threshold.
    - Long option: `--low`
    - Default: none (use the default foreground).
- `-S` _boolean_ Display optional suffixes
    - When set to a true designator ("True", "Yes" or "On"), optional
      value suffixes such as the '%' symbol or optional units will be
      displayed.
    - Long option: `--suffix`
    - Default: False.
- `-p` _number_ Percentages padding
    - Width, in number of digits, for quantities representing
      percentages. For instance `-p 3` means that all percentages
      in the monitor will be represented using 3 digits.
    - Long option: `--ppad`
    - Default value: 0 (don't pad)
- `-d` _number_ Decimal digits
    - Number of digits after the decimal period to use in float values.
    - Long option: `--ddigits`
    - Default value: 0 (display only integer part)
- `-m` _number_ Minimum field width
    - Minimum width, in number of characters, of the fields in the
      monitor template. Values whose printed representation is shorter
      than this value will be padded using the padding characters
      given by the `-c` option with the alignment specified by `-a`
      (see below).
    - Long option: `--minwidth`
    - Default: 0
- `-M` _number_ Maximum field width
    - Maximum width, in number of characters, of the fields in the
      monitor template. Values whose printed representation is longer
      than this value will be truncated.
    - Long option: `--maxwidth`
    - Default: 0 (no maximum width)
- `-w` _number_ Fixed field width
    - All fields will be set to this width, padding or truncating as
      needed.
    - Long option: `--width`
    - Default: 0 (variable width)
- `-T` _number_ Maximum total width
    - Maximum total width of the text.
    - Long option: `--maxtwidth`
    - Default: 0 (no limit)
- `-c` _string_
    - Characters used for padding. The characters of _string_ are used
      cyclically. E.g., with `-P +- -w 6`, a field with value "foo"
      will be represented as "+-+foo".
    - Long option: `--padchars`
    - Default value: " "
- `-a` r|l Field alignment
    - Whether to use right (r) or left (l) alignment of field values
      when padding.
    - Long option: `--align`
    - Default value: r (padding to the left)
- `-b` _string_ Bar background
    - Characters used, cyclically, to draw the background of bars.
      For instance, if you set this option to "·.", an empty bar will
      look like this: `·.·.·.·.·.`
    - Long option: `--bback`
    - Default value: ":"
- `-f` _string_ Bar foreground
    - Characters used, cyclically, to draw the foreground of bars.
    - Long option: `--bfore`
    - Default value: "#"
- `-W` _number_ Bar width
    - Total number of characters used to draw bars.
    - Long option: `--bwidth`
    - Default value: 10
- `-x` _string_ N/A string
    - String to be used when the monitor is not available
    - Long option: `--nastring`
    - Default value: "N/A"

Commands' arguments must be set as a list. E.g.:

    Run Weather "EGPF" ["-t", "<station>: <tempC>C"] 36000

In this case xmobar will run the weather monitor, getting information
for the weather station ID EGPF (Glasgow Airport, as a homage to GHC)
every hour (36000 tenth of seconds), with a template that will output
something like:

    Glasgow Airport: 16.0C


### `Uptime Args RefreshRate`

- Aliases to `uptime`
- Args: default monitor arguments. The low and high
  thresholds refer to the number of days.
- Variables that can be used with the `-t`/`--template` argument:
  `days`, `hours`, `minutes`, `seconds`. The total uptime is the
  sum of all those fields. You can set the `-S` argument to "True"
  to add units to the display of those numeric fields.
- Default template: `Up: <days>d <hours>h <minutes>m`

### `Weather StationID Args RefreshRate`

- Aliases to the Station ID: so `Weather "LIPB" []` can be used in
  template as `%LIPB%`
- Thresholds refer to temperature in the selected units
- Args: default monitor arguments
- Variables that can be used with the `-t`/`--template` argument:
	    `station`, `stationState`, `year`, `month`, `day`, `hour`,
	    `windCardinal`, `windAzimuth`, `windMph`, `windKnots`, `windMs`, `windKmh`
        `visibility`, `skyCondition`, `tempC`, `tempF`,
	    `dewPointC`, `dewPointF`, `rh`, `pressure`
- Default template: `<station>: <tempC>C, rh <rh>% (<hour>)`
- Retrieves weather information from http://weather.noaa.gov.

### `Network Interface Args RefreshRate`

- Aliases to the interface name: so `Network "eth0" []` can be used as
  `%eth0%`
- Thresholds refer to velocities expressed in Kb/s
- Args: default monitor arguments, plus:
  - `--rx-icon-pattern`: dynamic string for reception rate in `rxipat`.
  - `--tx-icon-pattern`: dynamic string for transmission rate in `txipat`.
- Variables that can be used with the `-t`/`--template` argument:
  `dev`, `rx`, `tx`, `rxbar`, `rxvbar`, `rxipat`, `txbar`, `txvbar`,
  `txipat`. Reception and transmission rates (`rx` and `tx`) are displayed
  by default as Kb/s, without any suffixes, but you can set the `-S` to
  "True" to make them displayed with adaptive units (Kb/s, Mb/s, etc.).
- Default template: `<dev>: <rx>KB|<tx>KB`

### `DynNetwork Args RefreshRate`

- Active interface is detected automatically
- Aliases to "dynnetwork"
- Thresholds are expressed in Kb/s
- Args: default monitor arguments, plus:
  - `--rx-icon-pattern`: dynamic string for reception rate in `rxipat`.
  - `--tx-icon-pattern`: dynamic string for transmission rate in `txipat`.
- Variables that can be used with the `-t`/`--template` argument:
  `dev`, `rx`, `tx`, `rxbar`, `rxvbar`, `rxipat`, `txbar`, `txvbar`,
  `txipat`. Reception and transmission rates (`rx` and `tx`) are displayed
  in Kbytes per second, and you can set the `-S` to "True" to make them
  displayed with units (the string "Kb/s").
- Default template: `<dev>: <rx>KB|<tx>KB`

### `Wireless Interface Args RefreshRate`

- Aliases to the interface name with the suffix "wi": thus, `Wireless
  "wlan0" []` can be used as `%wlan0wi%`
- Args: default monitor arguments, plus:
  - `--quality-icon-pattern`: dynamic string for connection quality in `qualityipat`.
- Variables that can be used with the `-t`/`--template` argument:
            `essid`, `quality`, `qualitybar`, `qualityvbar`, `qualityipat`
- Thresholds refer to link quality in a `[0, 100]` scale
- Default template: `<essid> <quality>`
- Requires the C library [iwlib] (part of the wireless tools suite)
  installed in your system. In addition, to activate this plugin you
  must pass `--flags="with_iwlib"` during compilation

### `Memory Args RefreshRate`

- Aliases to `memory`
- Args: default monitor arguments, plus:
  - `--used-icon-pattern`: dynamic string for used memory ratio in `usedipat`.
  - `--free-icon-pattern`: dynamic string for free memory ratio in `freeipat`.
  - `--available-icon-pattern`: dynamic string for available memory ratio in `availableipat`.
- Thresholds refer to percentage of used memory
- Variables that can be used with the `-t`/`--template` argument:
             `total`, `free`, `buffer`, `cache`, `available`, `used`,
             `usedratio`, `usedbar`, `usedvbar`, `usedipat`,
             `freeratio`, `freebar`, `freevbar`, `freeipat`,
             `availableratio`, `availablebar`, `availablevbar`, `availableipat`
- Default template: `Mem: <usedratio>% (<cache>M)`

### `Swap Args RefreshRate`

- Aliases to `swap`
- Args: default monitor arguments
- Thresholds refer to percentage of used swap
- Variables that can be used with the `-t`/`--template` argument:
	    `total`, `used`, `free`, `usedratio`
- Default template: `Swap: <usedratio>%`

### `Cpu Args RefreshRate`

- Aliases to `cpu`
- Args: default monitor arguments, plus:
  - `--load-icon-pattern`: dynamic string for cpu load in `ipat`
- Thresholds refer to percentage of CPU load
- Variables that can be used with the `-t`/`--template` argument:
	    `total`, `bar`, `vbar`, `ipat`, `user`, `nice`, `system`, `idle`, `iowait`
- Default template: `Cpu: <total>%`

### `MultiCpu Args RefreshRate`

- Aliases to `multicpu`
- Args: default monitor arguments, plus:
  - `--load-icon-pattern`: dynamic string for overall cpu load in `ipat`.
  - `--load-icon-patterns`: dynamic string for each cpu load in `autoipat`, `ipat{i}`.
                              This option can be specified several times. nth option
                              corresponds to nth cpu.
- Thresholds refer to percentage of CPU load
- Variables that can be used with the `-t`/`--template` argument:
	    `autototal`, `autobar`, `autovbar`, `autoipat`, `autouser`, `autonice`,
	    `autosystem`, `autoidle`, `total`, `bar`, `vbar`, `ipat`, `user`, `nice`,
	    `system`, `idle`, `total0`, `bar0`, `vbar0`, `ipat0`, `user0`, `nice0`,
	    `system0`, `idle0`, ...
  The auto* variables automatically detect the number of CPUs on the system
  and display one entry for each.
- Default template: `Cpu: <total>%`

### `Battery Args RefreshRate`

- Same as `BatteryP ["BAT0", "BAT1", "BAT2"] Args RefreshRate`.

### `BatteryP Dirs Args RefreshRate`

- Aliases to `battery`
- Dirs: list of directories in `/sys/class/power_supply/` where to
  look for the ACPI files of each battery. Example:
  `["BAT0","BAT1","BAT2"]`. Only the first 3 directories will be
  searched.
- Args: default monitor arguments, plus the following specific ones
  (these options, being specific to the monitor, are to be specified
  after a `--` in the argument list):
  - `-O`: string for AC "on" status (default: "On")
  - `-i`: string for AC "idle" status (default: "On")
  - `-o`: string for AC "off" status (default: "Off")
  - `-L`: low power (`watts`) threshold (default: 10)
  - `-H`: high power threshold (default: 12)
  - `-l`: color to display power lower than the `-L` threshold
  - `-m`: color to display power lower than the `-H` threshold
  - `-h`: color to display power higher than the `-H` threshold
  - `-p`: color to display positive power (battery charging)
  - `-f`: file in `/sys/class/power_supply` with AC info (default:
    "AC/online")
  - `--on-icon-pattern`: dynamic string for current battery charge
    when AC is "on" in `leftipat`.
  - `--off-icon-pattern`: dynamic string for current battery charge
    when AC is "off" in `leftipat`.
  - `--idle-icon-pattern`: dynamic string for current battery charge
    when AC is "idle" in `leftipat`.

- Variables that can be used with the `-t`/`--template` argument:
	    `left`, `leftbar`, `leftvbar`, `leftipat`, `timeleft`, `watts`, `acstatus`
- Default template: `Batt: <watts>, <left>% / <timeleft>`
- Example (note that you need "--" to separate regular monitor options from
  Battery's specific ones):

         Run BatteryP ["BAT0"]
                      ["-t", "<acstatus><watts> (<left>%)",
                       "-L", "10", "-H", "80", "-p", "3",
                       "--", "-O", "<fc=green>On</fc> - ", "-i", "",
                       "-L", "-15", "-H", "-5",
                       "-l", "red", "-m", "blue", "-h", "green"]
                      600

  In the above example, the thresholds before the "--" separator
  affect only the `<left>` and `<leftbar>` fields, while those after
  the separator affect how `<watts>` is displayed. For this monitor,
  neither the generic nor the specific options have any effect on
  `<timeleft>`.

  It is also possible to specify template variables in the `-O` and
  `-o` switches, as in the following example:

         Run BatteryP ["BAT0"]
                      ["-t", "<acstatus>"
                      , "-L", "10", "-H", "80"
                      , "-l", "red", "-h", "green"
                      , "--", "-O", "Charging", "-o", "Battery: <left>%"
                      ] 10

- The "idle" AC state is selected whenever the AC power entering the
  battery is zero.

### `BatteryN Dirs Args RefreshRate Alias`

Works like `BatteryP`, but lets you specify an alias for the monitor
other than "battery".  Useful in case you one separate monitors for
more than one battery.

### `TopProc Args RefreshRate`

- Aliases to `top`
- Args: default monitor arguments. The low and high
  thresholds (`-L` and `-H`) denote, for memory entries, the percent
  of the process memory over the total amount of memory currently in
  use and, for cpu entries, the activity percentage (i.e., the value
  of `cpuN`, which takes values between 0 and 100).
- Variables that can be used with the `-t`/`--template` argument:
	    `no`, `name1`, `cpu1`, `both1`, `mname1`, `mem1`, `mboth1`,
            `name2`, `cpu2`, `both2`, `mname2`, `mem2`, `mboth2`, ...
- Default template: `<both1>`
- Displays the name and cpu/mem usage of running processes (`bothn`
  and `mboth` display both, and is useful to specify an overall
  maximum and/or minimum width, using the `-m`/`-M` arguments. `no` gives
  the total number of processes.

### `TopMem Args RefreshRate`

- Aliases to `topmem`
- Args: default monitor arguments. The low and high
  thresholds (`-L` and `-H`) denote the percent of the process memory
  over the total amount of memory currently in use.
- Variables that can be used with the `-t`/`--template` argument:
	    `name1`, `mem1`, `both1`, `name2`, `mem2`, `both2`, ...
- Default template: `<both1>`
- Displays the name and RSS (resident memory size) of running
  processes (`bothn` displays both, and is useful to specify an
  overall maximum and/or minimum width, using the `-m`/`-M` arguments.

### `DiskU Disks Args RefreshRate`

- Aliases to `disku`
- Disks: list of pairs of the form (device or mount point, template),
  where the template can contain `<size>`, `<free>`, `<used>`, `<freep>` or
  `<usedp>`, `<freebar>`, `<freevbar>`, `<freeipat>`, `<usedbar>`,
  `<usedvbar>` or `<usedipat>` for total, free, used, free percentage and
  used percentage of the given file system capacity.
- Thresholds refer to usage percentage.
- Args: default monitor arguments. `-t`/`--template` is ignored. Plus
  - `--free-icon-pattern`: dynamic string for free disk space in `freeipat`.
  - `--used-icon-pattern`: dynamic string for used disk space in `usedipat`.
- Default template: none (you must specify a template for each file system).
- Example:

         DiskU [("/", "<used>/<size>"), ("sdb1", "<usedbar>")]
               ["-L", "20", "-H", "50", "-m", "1", "-p", "3"]
               20

### `DiskIO Disks Args RefreshRate`

- Aliases to `diskio`
- Disks: list of pairs of the form (device or mount point, template),
  where the template can contain `<total>`, `<read>`, `<write>` for total,
  read and write speed, respectively. There are also bar versions of each:
  `<totalbar>`, `<totalvbar>`, `<totalipat>`,
  `<readbar>`, `<readvbar>`, `<readipat>`,
  `<writebar>`, `<writevbar>`, and `<writeipat>`.
- Thresholds refer to speed in b/s
- Args: default monitor arguments. `-t`/`--template` is ignored. Plus
  - `--total-icon-pattern`: dynamic string for total disk I/O in `<totalipat>`.
  - `--write-icon-pattern`: dynamic string for write disk I/O in `<writeipat>`.
  - `--read-icon-pattern`: dynamic string for read disk I/O in `<readipat>`.
- Default template: none (you must specify a template for each file system).
- Example:

         DiskIO [("/", "<read> <write>"), ("sdb1", "<total>")] [] 10

### `ThermalZone Number Args RefreshRate`

- Aliases to "thermaln": so `ThermalZone 0 []` can be used in template
  as `%thermal0%`
- Thresholds refer to temperature in degrees
- Args: default monitor arguments
- Variables that can be used with the `-t`/`--template` argument:
	    `temp`
- Default template: `<temp>C`
- This plugin works only on systems with devices having thermal zone.
  Check directories in `/sys/class/thermal` for possible values of the
  zone number (e.g., 0 corresponds to `thermal_zone0` in that
  directory).
- Example:

         Run ThermalZone 0 ["-t","<id>: <temp>C"] 30

#### `Thermal Zone Args RefreshRate`

- **This plugin is deprecated. Use `ThermalZone` instead.**

- Aliases to the Zone: so `Thermal "THRM" []` can be used in template
  as `%THRM%`
- Args: default monitor arguments
- Thresholds refer to temperature in degrees
- Variables that can be used with the `-t`/`--template` argument:
	    `temp`
- Default template: `Thm: <temp>C`
- This plugin works only on systems with devices having thermal zone.
  Check directories in /proc/acpi/thermal_zone for possible values.
- Example:

         Run Thermal "THRM" ["-t","iwl4965-temp: <temp>C"] 50

### `CpuFreq Args RefreshRate`

- Aliases to `cpufreq`
- Args: default monitor arguments
- Thresholds refer to frequency in GHz
- Variables that can be used with the `-t`/`--template` argument:
	    `cpu0`, `cpu1`, ..,  `cpuN`
- Default template: `Freq: <cpu0>GHz`
- This monitor requires acpi_cpufreq module to be loaded in kernel
- Example:

         Run CpuFreq ["-t", "Freq:<cpu0>|<cpu1>GHz", "-L", "0", "-H", "2",
                      "-l", "lightblue", "-n","white", "-h", "red"] 50

### `CoreTemp Args RefreshRate`

- Aliases to `coretemp`
- Args: default monitor arguments
- Thresholds refer to temperature in degrees
- Variables that can be used with the `-t`/`--template` argument:
	    `core0`, `core1`, ..,  `coreN`
- Default template: `Temp: <core0>C`
- This monitor requires coretemp module to be loaded in kernel
- Example:

         Run CoreTemp ["-t", "Temp:<core0>|<core1>C",
                       "-L", "40", "-H", "60",
                       "-l", "lightblue", "-n", "gray90", "-h", "red"] 50

### `Volume Mixer Element Args RefreshRate`

- Aliases to the mixer name and element name separated by a colon. Thus,
  `Volume "default" "Master" [] 10` can be used as `%default:Master%`.
- Args: default monitor arguments. Also accepts:
    - `-O` _string_ On string
        - The string used in place of `<status>` when the mixer element
          is on. Defaults to "[on]".
        - Long option: `--on`
    - `-o` _string_ Off string
        - The string used in place of `<status>` when the mixer element
          is off. Defaults to "[off]".
        - Long option: `--off`
    - `-C` _color_ On color
        - The color to be used for `<status>` when the mixer element
          is on. Defaults to "green".
        - Long option: `--onc`
    - `-c` _color_ Off color
        - The color to be used for `<status>` when the mixer element
          is off. Defaults to "red".
        - Long option: `--offc`
    - `--highd` _number_ High threshold for dB. Defaults to -5.0.
    - `--lowd` _number_ Low threshold for dB. Defaults to -30.0.
    - `--volume-icon-pattern` _string_ dynamic string for current volume in `volumeipat`.
- Variables that can be used with the `-t`/`--template` argument:
            `volume`, `volumebar`, `volumevbar`, `volumeipat`, `dB`, `status`
- Note that `dB` might only return 0 on your system. This is known
  to happen on systems with a pulseaudio backend.
- Default template: `Vol: <volume>% <status>`
- Requires the package [alsa-core] and [alsa-mixer] installed in your
  system. In addition, to activate this plugin you must pass
  `--flags="with_alsa"` during compilation.

### `MPD Args RefreshRate`

- This monitor will only be compiled if you ask for it using the
  `with_mpd` flag. It needs [libmpd] 5.0 or later (available on Hackage).
- Aliases to `mpd`
- Args: default monitor arguments. In addition you can provide
  `-P`, `-S` and `-Z`, with an string argument, to represent the
  playing, stopped and paused states in the `statei` template field.
  The environment variables `MPD_HOST` and `MPD_PORT` are used to configure the
  mpd server to communicate with. Also available:
  - `lapsed-icon-pattern`: dynamic string for current track position in `ipat`.
- Variables that can be used with the `-t`/`--template` argument:
             `bar`, `vbar`, `ipat`, `state`, `statei`, `volume`, `length`,
             `lapsed`, `remaining`,
             `plength` (playlist length), `ppos` (playlist position),
             `flags` (ncmpcpp-style playback mode),
             `name`, `artist`, `composer`, `performer`,
             `album`, `title`, `track`, `file`, `genre`, `date`
- Default template: `MPD: <state>`
- Example (note that you need "--" to separate regular monitor options from
  MPD's specific ones):

         Run MPD ["-t",
                  "<composer> <title> (<album>) <track>/<plength> <statei> [<flags>]",
                  "--", "-P", ">>", "-Z", "|", "-S", "><"] 10

### `Mpris1 PlayerName Args RefreshRate`

- Aliases to `mpris1`
- Requires [dbus] and [text] packages.
  To activate, pass `--flags="with_mpris"` during compilation.
- PlayerName: player supporting MPRIS v1 protocol, in lowercase.
- Args: default monitor arguments.
- Variables that can be used with the `-t`/`--template` argument:
            `album`, `artist`, `arturl`, `length`, `title`, `tracknumber`
- Default template: `<artist> - <title>`
- Example:

         Run Mpris1 "clementine" ["-t", "<artist> - [<tracknumber>] <title>"] 10

### `Mpris2 PlayerName Args RefreshRate`

- Aliases to `mpris2`
- Requires [dbus] and [text] packages.
  To activate, pass `--flags="with_mpris"` during compilation.
- PlayerName: player supporting MPRIS v2 protocol, in lowercase.
- Args: default monitor arguments.
- Variables that can be used with the `-t`/`--template` argument:
            `album`, `artist`, `arturl`, `length`, `title`,
            `tracknumber`, `composer`, `genre`
- Default template: `<artist> - <title>`
- Example:

         Run Mpris2 "spotify" ["-t", "<artist> - [<composer>] <title>"] 10

### `Mail Args Alias`

- Args: list of maildirs in form
  `[("name1","path1"),...]`. Paths may start with a '~'
  to expand to the user's home directory.
- This plugin requires inotify support in your Linux kernel and the
  [hinotify] package. To activate, pass `--flags="with_inotify"`
  during compilation.
- Example:

         Run Mail [("inbox", "~/var/mail/inbox"),
                   ("lists", "~/var/mail/lists")]
                  "mail"

### `MBox Mboxes Opts Alias`

- Mboxes a list of mbox files of the form `[("name", "path", "color")]`,
  where name is the displayed name, path the absolute or relative (to
  BaseDir) path of the mbox file, and color the color to use to display
  the mail count (use an empty string for the default).
- Opts is a possibly empty list of options, as flags. Possible values:
   -a  --all (no arg)  Show all mailboxes, even if empty.
   -d dir  --dir dir a string giving the base directory where mbox files with
                     a relative path live.
   -p prefix --prefix prefix  a string giving a prefix for the list
                      of displayed mail counts
   -s suffix --suffix suffix  a string giving a suffix for the list
                      of displayed mail counts
- Paths may start with a '~' to expand to the user's home directory.
- This plugin requires inotify support in your Linux kernel and the
  [hinotify] package. To activate, pass `--flags="with_inotify"`
  during compilation.
- Example. The following command look for mails in `/var/mail/inbox`
  and `~/foo/mbox`, and will put a space in front of the printed string
  (when it's not empty); it can be used in the template with the alias
  `mbox`:

         Run MBox [("I ", "inbox", "red"), ("O ", "~/foo/mbox", "")]
                  ["-d", "/var/mail/", "-p", " "] "mbox"

### `XPropertyLog PropName`

- Aliases to `PropName`
- Reads the X property named by `PropName` (a string) and displays its
  value. The [samples/xmonadpropwrite.hs script] in xmobar's
  distribution can be used to set the given property from the output
  of any other program or script.

[samples/xmonadpropwrite.hs script]: https://github.com/jaor/xmobar/raw/master/samples/xmonadpropwrite.hs

### `UnsafeXPropertyLog PropName`

- Aliases to `PropName`
- Same as `XPropertyLog`, but the input is not filtered to avoid
  injection of actions (cf. `UnsafeXMonadLog`).  The program writing
  the value of the read property is responsible of performing any
  needed cleanups.

### `NamedXPropertyLog PropName Alias`

- Aliases to `Alias`
- Same as `XPropertyLog`, but a custom alias can be specified.

### `NamedXPropertyLog PropName Alias`

- Aliases to `Alias`
- Same as `UnsafeXPropertyLog`, but a custom alias can be specified.

### `Brightness Args RefreshRate`

- Aliases to `bright`
- Args: default monitor arguments, plus the following specif ones:
    - `-D`: directory in `/sys/class/backlight/` with files in it
       (default: "acpi_video0")
    - `-C`: file with the current brightness (default:
       actual_brightness)
    - `-M`: file with the maximum brightness (default:
       max_brightness)
    - `--brightness-icon-pattern`: dynamic string for current brightness in `ipat`.
- Variables that can be used with the `-t`/`--template` argument:
	    `vbar`, `percent`, `bar`, `ipat`
- Default template: `<percent>`
- Example:

       Run Brightness ["-t", "<bar>"] 60

### `Kbd Opts`

- Registers to XKB/X11-Events and output the currently active keyboard layout.
  Supports replacement of layout names.
- Aliases to `kbd`
- Opts is a list of tuples:
    -  first element of the tuple is the search string
    -  second element of the tuple is the corresponding replacement
- Example:

		Run Kbd [("us(dvorak)", "DV"), ("us", "US")]

### `Locks`

- Displays the status of Caps Lock, Num Lock and Scroll Lock.
- Aliases to `locks`
- Example:

	Run Locks

### `CatInt n filename`

- Reads and displays an integer from the file whose path is `filename`
  (especially useful with files in `/sys`).
- Aliases as `catn` (e.g. `Cat 0` as `cat0`, etc.) so you can
  have several.
- Example:

    Run CatInt 0 "/sys/devices/platform/thinkpad_hwmon/fan1_input" [] 50

### `UVMeter`

- Aliases to "uv " + station id. For example: `%uv brisbane%` or `%uv
  alice springs%`
- Args: default monitor arguments.

- *Reminder:* Keep the refresh rate high, to avoid making unnecessary
  requests every time the plug-in is run.
- Station IDs can be found here:
  http://www.arpansa.gov.au/uvindex/realtime/xml/uvvalues.xml
- Example:

        Run UVMeter "brisbane" ["-H", "3", "-L", "3", "--low", "green", "--high", "red"] 900

## Executing External Commands

In order to execute an external command you can either write the
command name in the template, in this case it will be executed without
arguments, or you can configure it in the "commands" configuration
option list with the Com template command:

`Com ProgramName Args Alias RefreshRate`

- ProgramName: the name of the program
- Args: the arguments to be passed to the program at execution time
- RefreshRate: number of tenths of second between re-runs of the
  command. A zero or negative rate means that the command will be
  executed only once.
- Alias: a name to be used in the template. If the alias is en empty
  string the program name can be used in the template.

E.g.:

        Run Com "uname" ["-s","-r"] "" 0

can be used in the output template as `%uname%` (and xmobar will call
_uname_ only once), while

        Run Com "date" ["+\"%a %b %_d %H:%M\""] "mydate" 600

can be used in the output template as `%mydate%`

## Other Plugins

<font size="+1">**`StdinReader`**</font>

- Aliases to StdinReader
- Displays any text received by xmobar on its standard input.
- Strips actions from the text received.  This means you can't pass dynamic
  actions via stdin.  This is safer than `UnsafeStdinReader` because there is
  no need to escape the content before passing it to xmobar's standard input.

<font size="+1">**`UnsafeStdinReader`**</font>

- Aliases to UnsafeStdinReader
- Displays any text received by xmobar on its standard input.
- Will not do anything to the text received.  This means you can pass dynamic
  actions via stdin.  Be careful to remove tags from dynamic text that you
  pipe-thru to xmobar's standard input, e.g. window's title.  There is no way
  to escape the tags, i.e. you can't print a literal `<action>` tag as a text
  on xmobar.
- Sample usage: send to xmobar's stdin the list of your workspaces enclosed by
  actions tags that switches the workspaces to be able to switch workspaces by
  clicking on xmobar:
  ```<action=`xdotool key alt+1`>ws1</action> <action=`xdotool key alt+1`>ws2</action>```

<font size="+1">**`Date Format Alias RefreshRate`**</font>

- Format is a time format string, as accepted by the standard ISO C
  `strftime` function (or Haskell's `formatCalendarTime`).
- Sample usage: `Run Date "%a %b %_d %Y <fc=#ee9a00>%H:%M:%S</fc>" "date" 10`

<font size="+1">**`DateZone Format Locale Zone Alias RefreshRate`**</font>

- Format is a time format string, as accepted by the standard ISO C
  `strftime` function (or Haskell's `formatCalendarTime`).
- If Locale is "" the default locale of the system is used, otherwise the given
  locale. If there are more instances of DateZone, using "" as input for Locale
  is not recommended.
- Zone is the name of the TimeZone. It is assumed that the tz database is stored
  in /usr/share/zoneinfo/. If "" is given as Zone, the default system time is
  used.
- Sample usage:
  `Run DateZone "%a %H:%M:%S" "de_DE.UTF-8" "Europe/Vienna" "viennaTime" 10`

<font size="+1">**`CommandReader "/path/to/program" Alias`**</font>

- Runs the given program, and displays its standard output.

<font size="+1">**`PipeReader "default text:/path/to/pipe" Alias`**</font>

- Reads its displayed output from the given pipe.
- Prefix an optional default text separated by a colon
- Expands environment variables in the first argument of syntax '${VAR}' or '$VAR'

<font size="+1">**`MarqueePipeReader "default text:/path/to/pipe" (length, rate, sep) Alias`**</font>

- Generally equivalent to PipeReader
- Text is displayed as marquee with the specified length, rate in 10th
  seconds and separator when it wraps around

        Run MarqueePipeReader "/tmp/testpipe" (10, 7, "+") "mpipe"

- Expands environment variables in the first argument

<font size="+1">
**`BufferedPipeReader Alias [(Timeout, Bool, "/path/to/pipe1"), ..]`**
</font>

- Display data from multiple pipes.
- Timeout (in tenth of seconds) is the value after which the previous
  content is restored i.e. if there was already something from a
  previous pipe it will be put on display again, overwriting the
  current status.
- A pipe with Timeout of 0 will be displayed permanently, just like
  `PipeReader`
- The boolean option indicates whether new data for this pipe should
  make xmobar appear (unhide, reveal). In this case, the Timeout
  additionally specifies when the window should be hidden again. The
  output is restored in any case.
- Use it for OSD-like status bars e.g. for setting the volume or
  brightness:

        Run BufferedPipeReader "bpr"
            [ (  0, False, "/tmp/xmobar_window"  )
            , ( 15,  True, "/tmp/xmobar_status"  )
            ]

  Have your window manager send window titles to
  `"/tmp/xmobar_window"`. They will always be shown and not reveal
  your xmobar.  Sending some status information to
  `"/tmp/xmobar_status"` will reveal xmonad for 1.5 seconds and
  temporarily overwrite the window titles.
- Take a look at [samples/status.sh]
- Expands environment variables for the pipe path

[samples/status.sh]: http://github.com/jaor/xmobar/raw/master/samples/status.sh


<font size="+1">**`XMonadLog`**</font>

- Aliases to XMonadLog
- Displays information from xmonad's `_XMONAD_LOG`. You can set this
  property by using `xmonadPropLog` as your log hook in xmonad's
  configuration, as in the following example (more info [here]):

        main = do
          spawn "xmobar"
          xmonad $ defaultConfig {
            logHook = dynamicLogString defaultPP >>= xmonadPropLog
          }
   This plugin can be used as a sometimes more convenient alternative
   to `StdinReader`. For instance, it allows you to (re)start xmobar
   outside xmonad.

[here]: http://xmonad.org/xmonad-docs/xmonad-contrib/XMonad-Hooks-DynamicLog.html

<font size="+1">**`UnsafeXMonadLog`**</font>

- Aliases to UnsafeXMonadLog
- Similar to StdinReader versus UnsafeStdinReader, this does not strip `<action
  ...>` tags from XMonad's `_XMONAD_LOG`.
- It is advised that you still use `xmobarStrip` for the ppTitle in your
  logHook:

        myPP = defaultPP { ppTitle = xmobarStrip }
        main = xmonad $ defaultConfig {
          logHook = dynamicLogString myPP >>= xmonadPropLog
        }

# Plugins

## Writing a Plugin

Writing a plugin for xmobar should be very simple. You need to create
a data type with at least one constructor.

Next you must declare this data type an instance of the `Exec` class, by
defining the 1 needed method (alternatively `start` or `run`) and 2
optional ones (alias and rate):

        start :: e -> (String -> IO ()) -> IO ()
        run   :: e -> IO String
        rate  :: e -> Int
        alias :: e -> String

`start` must receive a callback to be used to display the `String`
produced by the plugin. This method can be used for plugins that need
to perform asynchronous actions. See `Plugins/PipeReader.hs` for an
example.

`run` can be used for simpler plugins. If you define only `run` the
plugin will be run every second. To overwrite this default you just
need to implement `rate`, which must return the number of tenth of
seconds between every successive runs. See `Plugins/HelloWorld.hs` for
an example of a plugin that runs just once, and `Plugins/Date.hs` for
one that implements `rate`.

Notice that Date could be implemented as:

        instance Exec Date where
            alias (Date _ a _) = a
            start (Date f _ r) = date f r

        date :: String -> Int -> (String -> IO ()) -> IO ()
        date format r callback = do go
            where go = do
                    t <- toCalendarTime =<< getClockTime
                    callback $ formatCalendarTime defaultTimeLocale format t
                    tenthSeconds r >> go

This implementation is equivalent to the one you can read in
`Plugins/Date.hs`.

`alias` is the name to be used in the output template. Default alias
will be the data type constructor.

Implementing a plugin requires importing the plugin API (the `Exec`
class definition), that is exported by `Plugins.hs`. So you just need
to import it in your module with:

        import Plugins

After that your type constructor can be used as an argument for the
Runnable type constructor `Run` in the `commands` list of the
configuration options.

This requires importing your plugin into `Config.hs` and adding your
type to the type list in the type signature of `Config.runnableTypes`.

For a very basic example see `samples/Plugins/HelloWorld.hs` or the
other plugins that are distributed with xmobar.

## Installing/Removing a Plugin

Installing a plugin should require 3 steps. Here we are going to
install the HelloWorld plugin that comes with xmobar, assuming that
you copied it to `src/Plugins`:

1. import the plugin module in `Config.hs`, by adding:

        import Plugins.HelloWorld

2. add the plugin data type to the list of data types in the type
   signature of `runnableTypes` in `Config.hs`. For instance, for the
   HelloWorld plugin, change `runnableTypes` into:

        runnableTypes :: Command :*: Monitors :*: HelloWorld :*: ()
        runnableTypes = undefined

3. Rebuild and reinstall xmobar. Now test it with:

        xmobar Plugins/helloworld.config

As you may see in the example configuration file, the plugin can be
used by adding, in the `commands` list:

        Run HelloWorld

and, in the output template, the alias of the plugin:

        %helloWorld%

That's it.

To remove a plugin, just remove its type from the type signature of
runnableTypes and remove the imported modules.

To remove the system monitor plugin:

1. remove, from `Config.hs`, the line

        import Plugins.Monitors

2. in `Config.hs` change

         runnableTypes :: Command :*: Monitors :*: ()
         runnableTypes = undefined

    to

         runnableTypes :: Command :*: ()
         runnableTypes = undefined

3. rebuild xmobar.

# Authors and credits

Andrea Rossato originally designed and implemented xmobar up to
version 0.11.1. Since then, it is maintained and developed by [jao],
with the help of the greater xmobar and Haskell communities.

In particular, xmobar [incorporates patches] by Axel Angel, Dragos
Boca, Ben Boeckel, Duncan Burke, Roman Cheplyaka, Patrick Chilton,
Antoine Eiche, Nathaniel Wesley Filardo, John Goerzen, Reto Hablützel,
Juraj Hercek, Tomas Janousek, Spencer Janssen, Roman Joost, Jochen
Keil, Lennart Kolmodin, Krzysztof Kosciuszkiewicz, Dmitry Kurochkin,
Todd Lunter, Robert J. Macomber, Dmitry Malikov, David McLean, Marcin
Mikołajczyk, Dino Morelli, Tony Morris, Eric Mrak, Thiago Negri,
Edward O'Callaghan, Svein Ove, Martin Perner, Jens Petersen, Alexander
Polakov, Petr Rockai, Andrew Sackville-West, Markus Scherer, Alexander
Shabalin, Valentin Shirokov, Peter Simons, Alexander Solovyov, Will
Song, John Soros, Travis Staton, Artem Tarasov, Samuli Thomasson,
Edward Tjörnhammar, Sergei Trofimovich, Thomas Tuegel, Jan Vornberger,
Anton Vorontsov, Daniel Wagner, Zev Weiss, Phil Xiaojun Hu, Edward
Z. Yang and Norbert Zeh.

[jao]: http://jao.io
[incorporates patches]: http://www.ohloh.net/p/xmobar/contributors

## Thanks

__Andrea Rossato__:

Thanks to Robert Manea and Spencer Janssen for their help in
understanding how X works. They gave me suggestions on how to solve
many problems with xmobar.

Thanks to Claus Reinke for make me understand existential types (or at
least for letting me think I grasp existential types...;-).

__jao__:

Thanks to Andrea for creating xmobar in the first place, and for
giving me the chance to contribute.

# Useful links

- [Github page].
- [Mailing list].
- [xmobar's Ohloh page].

- To understand the internal mysteries of xmobar you may try reading
  [this tutorial] on X Window Programming in Haskell.

- My [sawflibs] project includes a module to automate running xmobar
  in [sawfish].

[xmobar's Ohloh page]: https://www.ohloh.net/p/xmobar
[this tutorial]: http://www.haskell.org/haskellwiki/X_window_programming_in_Haskell
[sawflibs]: http://github.com/jaor/sawflibs

# License

This software is released under a BSD-style license. See [LICENSE] for
more details.

Copyright &copy; 2010-2016 Jose Antonio Ortega Ruiz

Copyright &copy; 2007-2010 Andrea Rossato

[Github]: http://github.com/jaor/xmobar/
[Github page]: http://github.com/jaor/xmobar
[Hackage]: http://hackage.haskell.org/package/xmobar/
[LICENSE]: https://github.com/jaor/xmobar/raw/master/license
[Mailing list]: http://projects.haskell.org/cgi-bin/mailman/listinfo/xmobar
[MPD]: http://mpd.wikia.com/
[X11-xft]: http://hackage.haskell.org/package/X11-xft/
[i3status]: http://i3wm.org/i3status/
[i3status manual]: http://i3wm.org/i3status/manpage.html#_using_i3status_with_xmobar
[iwlib]: http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
[libasound]: http://packages.debian.org/stable/libasound2-dev
[hinotify]: http://hackage.haskell.org/package/hinotify/
[libmpd]: http://hackage.haskell.org/package/libmpd/
[dbus]: http://hackage.haskell.org/package/dbus
[text]: http://hackage.haskell.org/package/text
[sawfish]: http://sawfish.wikia.com/
[utf8-string]: http://hackage.haskell.org/package/utf8-string/
[alsa-core]: http://hackage.haskell.org/package/alsa-core
[alsa-mixer]: http://hackage.haskell.org/package/alsa-mixer
[timezone-olson]: http://hackage.haskell.org/package/timezone-olson
[timezone-series]: http://hackage.haskell.org/package/timezone-series
[libXpm]: http://cgit.freedesktop.org/xorg/lib/libXpm
[http-conduit]: http://hackage.haskell.org/package/http-conduit
[http-types]: http://hackage.haskell.org/package/http-types