1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
|
Installing Geiser.
------------------
Geiser is usable from its source tree, with no configuration
whatsoever, or can be installed from ELPA with `M-x install-package'
is Marmalade is in your list of archives. You can also (byte) compile
and install it with the usual configure/make/make install dance.
* From ELPA
Add Marmalade to your `package-archives' list:
(require 'package)
(add-to-list 'package-archives
'("marmalade" . "http://marmalade-repo.org/packages/"))
(package-initialize)
and run `M-x install-package RET geiser`. You can also use
http://download.savannah.gnu.org/releases/geiser/packages as a repo,
or download directly the package from there and use M-x
package-install-file.
* In place
- Extract the tarball or clone the git repository anywhere in your
file system. Let's call that place <path-to-geiser>.
- In your .emacs:
(load-file "<path-to-geiser>/elisp/geiser.el")
* Byte-compiled
- Create a build directory, `build', say:
$ cd <path-to-geiser>
$ mkdir build; cd build
- Configure and make:
$ ../configure && make
Now, you can use the byte-compiled Geiser in place by adding to
your .emacs:
(load "<path-to-geiser>/build/elisp/geiser-load")
or, alternatively, install it with:
$ make install
(you might need to get root access, depending on your installation
directory) and, instead of the above load forms, require
'geiser-install (not 'geiser, mind you) in your emacs
initialization file:
(require 'geiser-install)
* Chicken Addendum
These steps are necessary to fully support Chicken Scheme, but are
not required for any other scheme.
- Install the necessary support eggs:
$ chicken-install -s apropos chicken-doc
- Update the Chicken documentation database:
$ cd `csi -p '(chicken-home)'`
$ curl http://3e8.org/pub/chicken-doc/chicken-doc-repo.tgz | sudo tar zx
You're ready to go!
* Gambit Addendum
These steps are necessary to fully support all Gambit Scheme functionalities,
but are not required for any other scheme.
# SETUP :
1 - clone the last version of gambit and of this repo
2 - configure gambit using --enable-rtlib-debug-source to activate autodoc
``` bash
$ cd ~/
$ git clone "the gambit repo address"
$ cd gambit
$ ./configure --enable-single-host --enable-debug --enable-rtlib-debug-source
$ make bootstrap
$ make bootclean
$ make -j
$ make install
```
3 - put a link to geiser/elisp/geiser.el in your init file
in your init file paste :
``` elisp
(load-file "~/geiser/elisp/geiser.el")
```
(the path is your path to geiser.el.)
# setup REMOTE CONNECT TO A GAMBIT REPL
1 - you need to enable the gambit/geiser module
( if you can't, substitute the command below
with the PS: at the end of the readme )
``` bash
$ mkdir ~/gambit/lib/gambit/geiser
$ cp ~/geiser/geiser-module/* ~/gambit/lib/geiser/
```
2 - now that you have the module you start gsi with it and using the -:d@
``` bash
$ gsi -:d gambit/geiser -
```
3 - you can now open emacs and write
```
M-x geiser-connect gambit
```
Enjoy !
By the way, if you are unable to use gambit modules,
open gsi with the gambit.scm file
located in geiser/scheme/gambit/geiser/gambit.scm
something like : gsi -:d@ ~/geiser/scheme/gambit/geiser/gambit.scm -
Geiser's makefile accepts also all those other standard autotools
targets that you've come to know and love and that are documented
in virtually all boilerplate INSTALL files out there.
|
